全自動攪拌車的攪拌槽部件的使用
全自動攪拌車主要是用來運輸施工混凝土的卡車，使用的圓柱形攪拌筒運輸攪拌好的混凝土。在運輸過程中，攪拌筒可以保持轉動，這樣可以讓混凝土不會出現凝固現象。混凝土運輸完畢后，通常用水沖洗攪拌筒內部，以防止硬化的混凝土占用空間，減少攪拌筒的體積。那么，您對攪拌槽部件有多少了解呢？下面全自動攪拌車廠家小編就為大家介紹一下：
Full-automatic mixer truck is mainly used to transport construction concrete, and the cylindrical mixing drum is used to transport the mixed concrete. During transportation, the mixing drum can keep rotating, so that the concrete will not solidify. After the concrete is transported, the inside of the mixing drum is usually washed with water to prevent the hardened concrete from occupying space and reduce the volume of the mixing drum. So, how much do you know about mixing tank components? The following is a brief introduction to the manufacturer of automatic mixer:
攪拌罐是攪拌車的重要部件之一，要求的技術含量比較高，其技術含量會直接影響混凝土的質量，所以攪拌罐的設計比較高，公差范圍要小。攪拌槽內的葉片一般我們使用的是雙對數螺旋。
The mixing tank is one of the important parts of the mixing truck, which requires high technical content, which will directly affect the quality of concrete. Therefore, the design of the mixing tank is relatively high and the tolerance range is small. Generally, we use double logarithmic spiral for the blades in the mixing tank.
攪拌槽內的葉片有效的提高了混凝土的卸料的性能，出料口前的葉片上一般都帶有孔洞，這樣可以有效的降低了混凝土對葉片的粘結性能，提高出料的平均性。整個葉片從攪拌罐底部的滑動角度不斷增加，以確保葉片能充分攪拌混凝土，降低殘留率。
The blades in the mixing tank effectively improve the discharge performance of the concrete. The blades in front of the discharge port are generally provided with holes, which can effectively reduce the bonding performance of the concrete to the blades and improve the average of the discharge. The sliding angle of the whole blade from the bottom of the mixing tank is continuously increased to ensure that the blade can fully mix the concrete and reduce the residual rate.
我們知道一般攪拌罐的材質都會使用到高強度的鋼板，在攪拌罐成型后，拆下內支架，焊接葉片。焊接工藝我們一般使用的是碳氧化物保護膜，攪拌罐制作后進行噴丸處理，焊接和制作過程中產生的應力，提高鍍層的附著力。
We know that high strength steel plate will be used for the material of general mixing tank. After the mixing tank is formed, remove the inner support and weld the blades. We generally use carbon oxide protective film for welding process. After the mixing tank is manufactured, shot peening is carried out to eliminate the stress generated during welding and manufacturing and improve the adhesion of the coating.
關于全自動攪拌車的攪拌槽部件使用知識講解就是以上內容，相信大家一定對它更加感興趣了吧，更多信息歡迎來電http://www.bflrsn.cn咨詢。
The explanation of the use of the mixing tank components of the fully automatic mixer is the above content. I'm sure you are more interested in it. For more information, welcome to call http://www.bflrsn.cn consulting service
