中科攪拌機的零件破損速度怎么控制
如果你發現攪拌機的部件在使用過程中損壞得非常快，你必須找出具體的原因并它。現在讓我們來分析一下為什么攪拌器的部件分解得這么快。在中科攪拌機廠家幫大家查明原因之后，你就知道如何它了。
If you find that the parts of the mixer are damaged very quickly in use, you must find out the specific reason and solve it. Now let's analyze why the parts of the stirrer break down so fast. After we find out the reason for it, you will know how to solve it.
在機器工作怕的是機器零件損壞,不是有價值的一小部分,但影響了工作的進展是更麻煩的事情,尤其是當時間是不夠的,那么機器零件損壞將嚴重影響工作效率,今天小編給你介紹攪拌機配件損壞加快的原因。
Working in the machine is afraid of the damage of machine parts, not a small part of value, but it is the most troublesome thing to affect the progress of the work, especially when time is not enough, then the damage of machine parts will seriously affect the work efficiency. Today Xiaobian will introduce the reason why the damage of mixer parts accelerates.
攪拌器一般采用葉輪式攪拌器，設備配有輔助吸風口，通過調節板可適當開啟。當攪拌機工作時，攪拌后的原料能及時排出。如果調整的開板太小,空氣進入房間的數量并不大,混合室的負面壓力小,混合材料的放電不是的,混合材料太粉,在混合室的熱量不能及時排放,攪拌機必然會“發燒”。當攪拌機“發熱”時，必須檢查調節板的開度。
Generally, impeller agitator is used for agitator, and the equipment is equipped with auxiliary air suction port, which can be opened properly through regulating plate. When the mixer is working, the raw materials after mixing can be discharged in time. If the adjusted opening plate is too small, the amount of air entering the room is not large, the negative pressure in the mixing room is small, the discharge of the mixed material is not free, the mixed material is too powdery, the heat in the mixing room cannot be discharged in time, and the mixer will inevitably have a "fever". When the mixer is "hot", the opening of the regulating plate must be checked.
攪拌物料沉降室的空間要盡可能的大，這是道路暢通的保證，有利于攪拌物料的順利及時排出。因此在設計中應預留以滿足工藝要求。高速混合機錘擊,摩擦材料,材料中的水分和細粉塵將脈沖集塵袋袋粘連,風的阻力增加,隨著時間的增長,集塵袋風量和空氣壓力損失,嚴重時使軋機“發燒”,減少生產,必須及時更換或清洗集塵袋袋。
The space of the mixing material settling chamber shall be as large as possible, which is the guarantee of smooth road and is conducive to the smooth and timely discharge of the mixing material. Therefore, it should be reserved in the design to meet the process requirements. High speed mixer hammering, friction materials, moisture and fine dust in the materials will stick the pulse dust collection bag, and the resistance of the wind will increase. With the increase of time, the air volume and air pressure of the dust collection bag will be lost. In serious cases, the mill will have "fever" and production will be reduced. The dust collection bag must be replaced or cleaned in time.
攪拌機使用不當，長期處于超負荷工作狀態，還會引起攪拌機發熱，甚燒壞電機。良好的工作狀態是電機在90%的額定負載下工作。在正確分析機器磨損的原因后，我們可以積較地糾正機器正確的使用方式和正確的電壓。
Improper use of the mixer, long-term overload working state, will cause mixer heating, or even burn out the motor. Good working condition is that the motor works under 90% of rated load. After correctly analyzing the causes of machine wear, we can actively correct the correct use of the machine and the correct voltage.
這些都是可能導致攪拌機零件破碎速度的具體原因。我希望你把上面的問題講清楚后，能注意一下。
These are the specific reasons that may cause the crushing speed of mixer parts. I hope you can pay attention to the above questions after you have made them clear.
以上是中科攪拌機小編為大家介紹的相關內容，想要了解更多內容，歡迎訪問網站：http://www.bflrsn.cn
The above is the relevant content introduced by Zhongke blender. To learn more, please visit the website: http://www.bflrsn.cn
