攪拌車的油耗問題與什么有關？
一、故障的一般原因
1、 General cause of failure
1、空氣濾清器受堵，使進氣不暢，造成混合氣過濃，或排氣管受堵。
1. The air filter is blocked, so that the air inlet is not smooth, resulting in too rich mixture or blocked exhaust pipe.
2、怠速調整不正確。如CO調整錯誤。
2. The idle speed adjustment is incorrect. Such as co adjustment error.
3、發動機冷卻液溫度過高或過低。冷卻液溫度過高，冷卻液容易沸騰，動力下降，油耗增高；冷卻液溫度過低，混合氣霧化不好，發動機功率下降，油耗增加。
3. The engine coolant temperature is too high or too low. If the coolant temperature is too high, the coolant is easy to boil, the power decreases and the fuel consumption increases; The coolant temperature is too low, the mixture atomization is not good, the engine power decreases and the fuel consumption increases.
4、點火正時不準確，如點火過遲。
4. Incorrect ignition timing, such as too late ignition.
5、氣缸壓力過低。實踐證明，氣缸壓力低于規定值，燃油消耗增加20％～25％。
5. Cylinder pressure too low. Practice shows that the cylinder pressure is lower than the specified value, and the fuel consumption increases by 20% ~ 25%.
6、配氣相位不正確。
6. Incorrect valve timing.
7、廢氣再循環閥卡滯而常開。
7. Exhaust gas recirculation valve stuck normally open.
8、冬季使用夏季潤滑油或者機油加注過多。
8. Use lubricating oil in winter or fill too much oil in summer.
9、噴油器內部損壞或磨損嚴重。
9. Internal damage or severe wear of fuel injector.
10、發動機磨損嚴重。如拉缸、漏氣等。
10. The engine is severely worn. Such as cylinder pulling, air leakage, etc.
二、電控方面的原因
2、 Reasons for electronic control
1、冷卻液溫度傳感器有故障。如傳感器工作特性發生變化，就會造成噴油修正信號不準。
1. The coolant temperature sensor is faulty. If the working characteristics of the sensor change, the injection correction signal will be inaccurate.
2、進氣壓力傳感器有故障。如傳感器輸出壓力過高，勢必造成混合氣過濃。
2. The intake pressure sensor is faulty. If the output pressure of the sensor is too high, the mixture will be too rich.
3、進氣溫度傳感器有故障。
3. The intake air temperature sensor is faulty.
4、氧傳感器有故障。如傳感器內部短路，傳感器電壓為0，電腦接收稀混合氣信號指令增加噴油量。
4. The oxygen sensor is faulty. If the sensor has an internal short circuit and the sensor voltage is 0, the computer receives the lean mixture signal and instructs to increase the fuel injection quantity.
5、節氣門位置傳感器有故障。如節氣門位置信號錯誤。
5. The throttle position sensor is faulty. If the throttle position signal is incorrect.
6、空氣流量計有故障。
6. The air flow meter is faulty.
7、油壓調節器有故障。
7. The oil pressure regulator is faulty.
8、ECU及連接器有故障。
8. ECU and connector are faulty.
9、爆燃傳感器有故障。
9. The knock sensor is faulty.
10、活性炭罐有故障。
10. The activated carbon canister is faulty.
下一篇：攪拌車變速箱維修要注意什么？上一篇：1.6方旋轉自動上料攪拌車快速問題
