自上料攪拌車攪拌軸停止轉動的原因
自上料攪拌車攪拌軸停止轉動的原因是什么呢？實際上，在生產過程中當出現混凝土自上料攪拌車攪拌軸停止轉動或是轉動有點緩慢都是正?，F象，如果這種情況先停機檢查，看看有沒有出現下列三種情況，下面自上料攪拌車廠家為您講解：
What is the reason why the mixing shaft of the self feeding mixer truck stops rotating? In fact, it is normal for the mixing shaft of the concrete self loading mixer to stop rotating or rotate slowly during the production process. If this situation occurs, stop the machine first and check to see if the following three situations have occurred. Below, the manufacturer of the self loading mixer will explain to you:
1、電機傳動皮帶有沒有出現松動的情況?自拌混凝土攪拌車電機傳動皮帶過松也能導致商品混凝土拌合機攪拌軸轉動緩慢或者停止轉動，電機傳動皮帶過松，導致傳遞的動力不足。
1. Is there any looseness in the motor drive belt? Loose motor drive belt of the self mixing concrete mixer can also cause the mixing shaft of the commercial concrete mixer to rotate slowly or stop rotating. Loose motor drive belt can lead to insufficient power transmission.
2、有沒有嚴重超載?自拌混凝土攪拌車攪拌軸如果超過正常工作負荷，會使攪拌軸轉動緩慢，若負荷過大，就會導致攪拌軸停轉或者是攪拌軸彎曲。
2. Is there a serious overload? If the mixing shaft of the self mixing concrete mixer exceeds the normal working load, it will cause the mixing shaft to rotate slowly. If the load is too large, it will cause the mixing shaft to stop rotating or bend.
3、攪拌葉片或側葉片與筒體內壁間有沒有大的異物?出現這種情況也會使混凝土自動上料攪拌車攪拌軸停止轉動或轉動緩慢。攪拌葉片或側葉片與罐內壁間有較大的異物也會導致攪拌軸停轉，之所以能卡存異物，就是由于攪拌葉片或側葉片與罐內壁間隙過大造成的，尤其是石子。
3. Are there any large foreign objects between the mixing blades or side blades and the inner wall of the cylinder? This situation can also cause the mixing shaft of the automatic concrete loading mixer to stop rotating or rotate slowly. The presence of large foreign objects between the mixing blades or side blades and the inner wall of the tank can also cause the mixing shaft to stop rotating. The reason why foreign objects can be stuck is due to the large gap between the mixing blades or side blades and the inner wall of the tank, especially stones.
此外有關的保養事項也要多加注意，比如：
In addition, pay more attention to maintenance matters, such as:
調整氣動自動開關的上限和下限。如果壓力太低，氣缸會減速，如果壓力太高，氣動系統的氣密性會降低。
Adjust the upper and lower limits of the pneumatic automatic switch. If the pressure is too low, the cylinder will slow down, and if the pressure is too high, the airtightness of the pneumatic system will decrease.
使用自上料攪拌車檢查油位，并確保油位在量油尺的頂線和底線之間。當油位接近下，添加新油。
Use a self loading mixer truck to check the oil level and ensure that it is between the top and bottom lines of the dipstick. When the oil level approaches the lower limit, add new oil.
確保皮帶正確張緊。用手指推動皮帶，使其松開約10毫米。更換傳送帶時，必須更換整個組以保持共同的張力。
Ensure that the belt is properly tensioned. Push the belt with your fingers to loosen it by approximately 10 millimeters. When replacing the conveyor belt, the entire group must be replaced to maintain a common tension.
由于氣體系統中充滿油，因此需要足夠量的油才能正常運行。只有這樣，才能同時使用獨立式混合器的功率來延長氣體系統的使用壽命。
Due to the gas system being filled with oil, a sufficient amount of oil is required for normal operation. Only in this way can the power of the independent mixer be used simultaneously to extend the service life of the gas system.
自上料攪拌車攪拌軸停止轉動的原因就講解到這里了，希望能夠給您好的幫助，更多事項了解就來我們網站http://www.bflrsn.cn咨詢吧！
That's all for explaining the reason why the mixing shaft of the self feeding mixer truck stopped rotating. I hope it can be helpful to you. For more information, please come to our website http://www.bflrsn.cn Consult!
下一篇：全自動攪拌車在修橋工程中的優勢上一篇：使用自動上料攪拌車的幾個要點
