自上料攪拌機的剎車系統和料門有哪些需要注意的呢？
自上料攪拌機在日常使用中制動系統和剎車系統相對來說很重要，直接對接著自身安全，所以說這點很重要，需要好好了解下剎車系統如何？
Since the charging mixer in daily use, the brake system and brake system are relatively important, directly for their own safety, so this is very important, we need to have a good understanding of the braking system?
斷氣剎制動氣室內有個強力繃簧，行車時壓縮空氣將繃簧頂起。手剎車就是把氣放掉，讓繃簧把剎車鎖死。行車中氣壓過低時也會發生剎車效應，保證安全。慣例剎車是手剎鎖住傳動軸，腳瞬時由壓縮空氣進入制動氣室鎖住車輪。在手剎或傳動軸機械毛病時，手剎失靈;在氣泵、管路、儲氣筒、制動閥任何一個部位毛病時，腳剎失靈。而斷氣剎車就可有用避免這些風險。
There is a strong tension spring in the brake air chamber of the air cut brake, which is jacked up by compressed air when driving. The handbrake is to let the air out and let the tension spring lock the brake. When the air pressure is too low, the braking effect will occur to ensure safety. The conventional brake is that the hand brake locks the transmission shaft, and the foot enters the brake chamber by compressed air instantaneously to lock the wheels. In case of mechanical failure of hand brake or transmission shaft, the hand brake fails; when any part of air pump, pipeline, air reservoir and brake valve fails, the foot brake fails. The air brake can be useful to avoid these risks.
由于旅行開關未能修理或更換。絞車過熱主要是由于制動裝置間隙不當造成的。 會造成什么后果，今天就簡單來了解下中科自上料攪拌機的配料門吧：
The travel switch could not be repaired or replaced. The overheating of winch is mainly caused by improper clearance of brake device. What are the consequences? Let's learn about the mixing gate of the charging mixer
配料機的進料門工作不正常。 主要原因是門和門框之間的間隙太大或門變形。 門被沙子和礫石擋住了。 糾正材料門或更換材料門或橡膠板。 攪拌車氣缸力小，需要檢查氣源壓力或修理氣缸。料斗偏向或卡住。 這主要是由于兩個凸起的芯或芯的跳線長度不一致。可以通過調節燈芯的長度，調節靈敏度的下限和調節防跳裝置來解決。卸下料斗后，無法控制跌落。
The feeding door of the batching machine is not working properly. The main reason is that the gap between the door and the door frame is too large or the door is deformed. The door was blocked by sand and gravel. Correct material door or replace material door or rubber plate. The cylinder force of the mixer is small, so it is necessary to check the air source pressure or repair the cylinder. The hopper is deflected or jammed. This is mainly due to the inconsistency of the jumper length of two protruding cores or cores. It can be solved by adjusting the length of the wick, adjusting the lower limit of sensitivity and adjusting the anti bounce device. After unloading the hopper, the drop cannot be controlled.
以上還是敢于自上料攪拌機剎車方式和料門出現問題的解決方法的相關介紹，希望對你們有所幫助，想要了解更多內容歡迎點擊http://www.bflrsn.cn中科自上料攪拌機官網。
The above or dare from the charging mixer brake mode and material door problems related to the introduction, hope to help you, want to learn more content, welcome to click http://www.bflrsn.cn Zhongke from the official website of charging mixer.
下一篇：中科自上料攪拌機的操作優勢有哪些？上一篇：混凝土攪拌車卸料的注意事項！
